Author Topic: EMI/EMC design tips for NHD-4.3-480272EF-ATXL#  (Read 3771 times)


  • Newbie
  • *
  • Posts: 1
  • Karma: 0
    • View Profile
EMI/EMC design tips for NHD-4.3-480272EF-ATXL#
« on: December 09, 2016, 02:40:01 PM »
Hello everyone,

We use the NHD-4.3-480272EF-ATXL# TFT display in the front console of one of our product designs (a 19'' rack mounted industrial control unit). We resently did some pre-compliance testing for EMC and during the emission test we had a big chunk of interference around 200MHz which seemed to be related to the display (i.e. turning it off made the interference go away).

We did not put much care to the EMI desing of the front consola assembly (and it shows!), so now we a reviewing the design with this in mind and I had a couple of questions:

1) Should the TFT bezel be grounded?
2) We are making sure that all TFT signals are now running over a solid ground plane for both signal integrity and reduced emissions. What should the trace impedance be? Is 50ohm OK?

Any other tips will be much appreciated!

Thank you all in advance.



  • Administrator
  • Hero Member
  • *****
  • Posts: 303
  • Karma: 17
    • View Profile
Re: EMI/EMC design tips for NHD-4.3-480272EF-ATXL#
« Reply #1 on: December 09, 2016, 03:44:53 PM »
Below are a few tips that should help improve your design:
   Ground the TFT's bezel
   Utilize flat cable Ferrite core (used for FPC/FFC cable)
   Utilize EMI shielding foils and film
   Place 33 Ohm resistors in series on the display lines to help improve EMI performance

Please note that the bezel can act as a shield keeping noise from other system components it must be well grounded to provide the best immunity.

Shielding techniques can go a long way toward reducing electromagnetic/RF interference (EMI) and delivering reliable systems.

Hope this helps, feel free to contact me if you have any questions or concerns.

Joachim Geiger

  • Newbie
  • *
  • Posts: 1
  • Karma: 0
    • View Profile
Re: EMI/EMC design tips for NHD-4.3-480272EF-ATXL#
« Reply #2 on: January 23, 2017, 02:49:06 AM »
Dear Paul,
we use also the NHD-4.3-480272EF-ASXN#-T for a electric drive visualisation for ultralight planes.
There are strong emissions at 120Mhz, the frequency for the aeronautical radio service, comming from the display.
You wrote about the possiblity to reduce EMI with 33 ohm resistors in series to the display lines, and/or ferrite's for the FFC-Cable.
Is there a scheme available in which lines the resistors should be placed and how to use the ferrite's?

Thank you in advance.


  • Newbie
  • *
  • Posts: 6
  • Karma: 0
    • View Profile
Re: EMI/EMC design tips for NHD-4.3-480272EF-ATXL#
« Reply #3 on: October 16, 2017, 04:54:13 PM »
Ferrite and resistor you must place close as possible to clock (emission) source. In this case I think that your I/O port in microcontroller.


NHD‐3.5‐320240MF‐ATXL#‐T‐1 Touch Signal

Started by jmasamotoBoard TFTs

Replies: 1
Views: 5588
Last post February 05, 2016, 08:05:40 AM
by Paul_B
NHD‐3.5‐320240MF‐ATXL#‐CTP‐1 Problem with standby mode

Started by guenterBoard TFTs

Replies: 0
Views: 5523
Last post June 16, 2016, 12:14:36 PM
by guenter
NHD-5.0-800480TF-ATXL#-T and NHD-5.0-800480TF-20 Controller Board No Touch?

Started by dfanslerBoard TFTs

Replies: 5
Views: 6560
Last post May 26, 2017, 11:10:57 AM
by Saurabh_B
NHD-5.0-800480TF-ATXL#-CTP why don't typical timing values work?

Started by jkelleherBoard TFTs

Replies: 2
Views: 5378
Last post August 31, 2015, 05:08:45 AM
by jmag999
NHD-3.5-320240MF-ATXL#-CTP-1 Ft5x06 Linux device tree

Started by rajarajan.rBoard TFTs

Replies: 1
Views: 5459
Last post July 05, 2016, 01:21:43 PM