Author Topic: Capacitive touch problems under linux (FT5x06)  (Read 27490 times)

Michael_L

  • Administrator
  • Hero Member
  • *****
  • Posts: 357
  • Karma: 34
    • View Profile
Re: Capacitive touch problems under linux (FT5x06)
« Reply #15 on: July 14, 2014, 08:46:04 AM »
Thanks again for sharing your solution, I have added this to the datasheet.  Please allow a day or so for this to reflect on our website.

chrisu

  • Newbie
  • *
  • Posts: 2
  • Karma: 0
    • View Profile
Re: Capacitive touch problems under linux (FT5x06)
« Reply #16 on: July 15, 2014, 10:19:41 PM »
I understand this may be a shot in the dark, but would you mind posting a link to the kernel driver you found that was workable? I am using the same 7" display in a prototype I am working on, and have had a difficult time with the module sources I tried using/modifying so far.

abhishekjain2407

  • Newbie
  • *
  • Posts: 4
  • Karma: 0
    • View Profile
Re: Capacitive touch problems under linux (FT5x06)
« Reply #17 on: July 21, 2014, 04:42:57 PM »
Can you please share the firmware driver for this module under linux because it is not a part of standard linux distribution from TI. I am using the same and will appreciate if you provide that as i could save some time.

Michael_L

  • Administrator
  • Hero Member
  • *****
  • Posts: 357
  • Karma: 34
    • View Profile
Re: Capacitive touch problems under linux (FT5x06)
« Reply #18 on: July 22, 2014, 09:37:10 AM »
We have a linux driver available for the capacitive touch panel, and if you would like it please email nhtech@newhavendisplay.com.

abhishekjain2407

  • Newbie
  • *
  • Posts: 4
  • Karma: 0
    • View Profile
Re: Capacitive touch problems under linux (FT5x06)
« Reply #19 on: July 22, 2014, 12:32:21 PM »
I have just sent an email to the address provided.

Thanks

Abhishek

vpd

  • Jr. Member
  • **
  • Posts: 10
  • Karma: 0
    • View Profile

yraeisi

  • Newbie
  • *
  • Posts: 3
  • Karma: 0
    • View Profile
Re: Capacitive touch problems under linux (FT5x06)
« Reply #21 on: July 18, 2018, 01:07:41 AM »
The I2C protocol between the two displays should be the same.  Do you have another 4.3" TFT with capacitive touch panel to try?

Hi VPD
can you tell me,how did you increase the sensitivity of 7" CTP?
which Registers must be modified?
I need CTP work with 4mm Glass cover Lens.
thanks so much

 

NHD‐3.5‐320240MF‐ATXL#‐T‐1 Touch Signal

Started by jmasamotoBoard TFTs

Replies: 1
Views: 4483
Last post February 05, 2016, 08:05:40 AM
by Paul_B
NHD‐2.4‐240320SF‐CTXL#‐FTN1 touch-screen problem

Started by hbcelebiBoard TFTs

Replies: 5
Views: 7677
Last post December 10, 2014, 11:19:05 AM
by Michael_L
Problems with a NHD‐0420H1Z‐FL‐GBW‐3V3

Started by c2hollowBoard Character LCDs

Replies: 7
Views: 7185
Last post July 17, 2017, 08:17:45 AM
by Saurabh_B
NHD-5.0-800480TF-ATXL#-T and NHD-5.0-800480TF-20 Controller Board No Touch?

Started by dfanslerBoard TFTs

Replies: 5
Views: 4608
Last post May 26, 2017, 11:10:57 AM
by Saurabh_B
NHD-7.0-800480EF-ASXV#-CTP - "Touch" stopped working on part of LCD

Started by coran21Board TFTs

Replies: 0
Views: 34
Last post October 19, 2018, 10:10:46 AM
by coran21