1
TFTs / Re: NHD-5.0-800480TF-ATXL#-CTP invert PCLK polarity
« on: November 22, 2016, 04:59:51 AM »
Hi, finally I inverted R19 and R20 to test. It works.
Regards, Pierre
Regards, Pierre
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
TFTs / NHD-5.0-800480TF-ATXL#-CTP invert PCLK polarity
« on: November 22, 2016, 04:28:46 AM »
Hello,
Thanks to this post, http://www.newhavendisplay.com/NHD_forum/index.php/topic,1757.0.html , I would like to invert PCLK polarity of my new NHD-5.0-800480TF-ATXL#-CTP display.
I have a new hardware version, so I would like to check with you if inverting R19 shorted and R20 open will answer my question.
Attached, I took a picture of my new hardware.
Regards,
Pierre
[attachment deleted by admin]
Thanks to this post, http://www.newhavendisplay.com/NHD_forum/index.php/topic,1757.0.html , I would like to invert PCLK polarity of my new NHD-5.0-800480TF-ATXL#-CTP display.
I have a new hardware version, so I would like to check with you if inverting R19 shorted and R20 open will answer my question.
Attached, I took a picture of my new hardware.
Regards,
Pierre
[attachment deleted by admin]
3
TFTs / Re: NHD-5.0-800480TF-ATXL#-CTP HV mode
« on: March 11, 2016, 07:54:08 AM »
Morning Paul 
Hard changing PCLK polarity (R9-R10) solved the problem ! Image is good quality now. I was sure to software invert PCLK but it wasn't...
Many thanks!
Pierre
Hard changing PCLK polarity (R9-R10) solved the problem ! Image is good quality now. I was sure to software invert PCLK but it wasn't...
Many thanks!
Pierre
4
TFTs / Re: NHD-5.0-800480TF-ATXL#-CTP HV mode
« on: March 10, 2016, 03:01:55 AM »
Hello Paul,
Thanks for your reply. Unfortunately, I'm little confused. When I read first line, I understand default is SYNC mode. On my default PCB, R18 is open and R17 is shorted. On second line, you write it equals DE+SYNC mode. Which modes are :
- R18(open)/R17(shorted) ?
- R18(shorted)/R17(open) ?
About PCLK polarity, R19 and R20 are both connected on my PCB. I took a photo (pcb.jpg) of the display PCB to be sure we are talking about the same resistors.
Edit : Note : On photo, I switched R8/R7 resistors (before you edit your post). Other components are default.
Thank you for your support
, Pierre
ps : the captcha is really hard to read !
[attachment deleted by admin]
Thanks for your reply. Unfortunately, I'm little confused. When I read first line, I understand default is SYNC mode. On my default PCB, R18 is open and R17 is shorted. On second line, you write it equals DE+SYNC mode. Which modes are :
- R18(open)/R17(shorted) ?
- R18(shorted)/R17(open) ?
About PCLK polarity, R19 and R20 are both connected on my PCB. I took a photo (pcb.jpg) of the display PCB to be sure we are talking about the same resistors.
Edit : Note : On photo, I switched R8/R7 resistors (before you edit your post). Other components are default.
Thank you for your support
, Pierreps : the captcha is really hard to read !
[attachment deleted by admin]
5
TFTs / NHD-5.0-800480TF-ATXL#-CTP HV mode
« on: March 09, 2016, 04:22:56 AM »
Hello,
I use NHD-5.0-800480TF-ATXL#-CTP with Android 5.0. I could configure screen size to reach TFT active area but image is medium quality. I have some blinking pixels or red/blue pixels. I would like to try another synchronization mode.
Thanks to this post, http://www.newhavendisplay.com/NHD_forum/index.php/topic,1091.msg2582/topicseen.html#msg2582 , I think the display is DE mode. How could I change to HV mode ?
Regards, Pierre
I use NHD-5.0-800480TF-ATXL#-CTP with Android 5.0. I could configure screen size to reach TFT active area but image is medium quality. I have some blinking pixels or red/blue pixels. I would like to try another synchronization mode.
Thanks to this post, http://www.newhavendisplay.com/NHD_forum/index.php/topic,1091.msg2582/topicseen.html#msg2582 , I think the display is DE mode. How could I change to HV mode ?
Regards, Pierre
Pages: [1]