App Notes | Support Forum | Site Feedback | Newhaven Newsletter Follow us on Twitter Follow us on Facebook Our YouTube Channel Our GitHub Repository



  MISC. LCD Information
  Controller/Driver Datasheets
  Example Program Code
  NHDev Kit Assembly Guide
  Touch Panel Information
  Available Font Tables
Serial vs Parallel Interface
  Custom Keypads

Newhaven Display International has LCDs, TFTs and OLEDs that offer both modes: parallel and serial. A multi-interface LCD board is designed to display information on the LCD using different parallel or serial protocol interfaces. Only one protocol will write to the LCD at a time.  Some controller IC’s have more than one user-selectable interface option. No matter which protocol is being used to interface to the LCD, it must be initialized prior to normal use.

Below you will learn more about parallel and serial interface so you may better understand what this means when deciding on a product.

There are two ways of transmitting a byte between two digital devices. We can either transmit the byte in PARALLEL or we can transmit the byte in SERIAL form.  The drawing to the left illustrates the differences between these two types of communication mechanisms.

In parallel mode, each bit has a single wire devoted to it and all the bits are transmitted at the same time. In serial mode, the bits are transmitted as a series of pulses.

Goodwine, Bill. “Serial Communication.” 2002. University of Notre Dame. 22 Feb. 2012 <>.  

Serial Interface
(one bit at a time)


Parallel Interface
(multiple bits at a time)

Serial interface consists of an I2C bus, SPI bus, or synchronous serial control and data lines. The biggest advantage of the serial interface displays is they use fewer pins. You save connection pins, board traces and I/O pins. Although a downside is that you usually can't read from the display in serial mode, only write. Also, it's normally slower in serial interface than writing in parallel.

Serial Interface Types

 - Synchronous Serial - Serial Data In, Register Select, Reset, & Serial Clock

  •  Custom - Various configurations - may include
      Chip Select

 - SPI (Serial Peripheral Interface)

  •  SPI (3 wire) uses Serial Data Out, Serial Data In, and Serial Clock

  •  SPI (4 wire) adds Chip Select

Timing and operation may differ from usual SPI

 - I2C uses Serial Data Line and Serial Clock
 - LCD controller has certain usable I2C bus addresses
 - Requires pull-up resistors
 - May not function correctly with other devices on same bus

SPI Interface

SPI interface operates in full duplex mode, meaning that the devices can communicate with one another simultaneously. For this to work, two data lines are required. With this standard, devices communicate in a master/slave mode, where the master device (host processor) initiates the data and the clock. The LCD/OLED display is the peripheral slave device(s) attached to the data bus. Multiple peripherals are addressed on the same serial data bus. But keep in mind, the display will only listen to the data it sees when the Chip Select line is active (usually low). If the Chip Select line is inactive (usually High), the display listens to the data on the bus, but ignores it. During this state, the SDO line isn't active.


Parallel interface consists of 8 data pins and 3 control lines. The control lines used are Enable (E), Register Select (RS), and Read/Write (R/W). RS is used to signal when a command or data is being sent to the display. Enable tells the display that the data or instruction in the register is ready to be interpreted by the display. The Read/Write tells the display whether to write data or read data from the register. 4-bit parallel interface works exactly like the standard 8-bit interface, only each byte of data sent or received is clocked into the display one nibble at a time. After every two clock cycles, the entire byte is combined and executed like an 8-bit command.

In addition to the following common interface connection examples, some displays may include additional control lines.

    - V0 - Contrast Adjustment
    - CS - Chip Select
    - BUSY - Typically a low state indicates busy state

Serial Interface Types

  •  16 Bit Data - Not Common - used on some TFT
  •  8 Bit Data - Most Common - used on graphic and
      character controllers
  •  4 Bit Data – A common option on character controllers
  •  8080 type - Parallel Data with Write Line and Read Line
  •  6800 type - Parallel Data, with Read/Write Line and
      Enable Line



Contact Us | Customer Loyalty Program

Site Map | Terms and Conditions | Job Opportunities | SSL Certificate