Author Topic: NHD-C0220BiZ-FSW-FBW-3V3M Problem -- Doesn't power on  (Read 3161 times)

seilcomp

  • Newbie
  • *
  • Posts: 3
  • Karma: 0
    • View Profile
NHD-C0220BiZ-FSW-FBW-3V3M Problem -- Doesn't power on
« on: December 08, 2015, 01:51:42 AM »
Dear Sir;
 
I want to use this LCD with MSP430.

I purchased 2 pices of the sample LCD and hooked up to 3.2VDC (VCC from MSP430F5528). And I hooked up the capacitors and the pull-up resistors. I only have to connect to RST, SDA, SCL to finish the connection. But I believed, though I'm a total newbie, that I'll be able to see the display will respond by lighting up the screen when I connect the power.

But until now, nothing comes on. Shall I finish connecting the remainder of the pins to see the LCD power on>?

Also, the data sheet is kind of confusing or misleading. On the drawing, it says the pin numbers are from 8 to 1 (from left to right). But on page 4, the pin order is the other way around. Which instruction should I follow?

Please help this pitiful newbie.

Suh, Sukho from Seoul, Korea

Paul_B

  • Administrator
  • Sr. Member
  • *****
  • Posts: 249
  • Karma: 16
    • View Profile
Re: NHD-C0220BiZ-FSW-FBW-3V3M Problem -- Doesn't power on
« Reply #1 on: December 08, 2015, 08:48:16 AM »
Hello Sukho!

Iím sorry to hear about the trouble you are having with NHD-C0220BiZ-FSW-FBW-3V3M. Before you can really use the LCD, you must initialize and configure it. This is accomplished by sending a number of initialization instructions to the LCD.

Please see our "Example Initialization Program" listed on page 11 in the displays datasheet:

http://www.newhavendisplay.com/specs/NHD-C0220BiZ-FSW-FBW-3V3M.pdf

Next, it would be helpful to verify your wiring / pinout. Feel free to post it below.

Finally the pin connection / wiring diagram in the displays datasheet is correct. The pin numbering listed in the mechanical drawing 8 - 1 (left to right) is there to help distinguish the correct pin order.

Please following the pin description table listed on page 4 in the displays datasheet and take special note of where pin 1 is located on the physical display when wiring.

Hope this helps!






« Last Edit: December 09, 2015, 11:33:32 AM by Paul_B »

seilcomp

  • Newbie
  • *
  • Posts: 3
  • Karma: 0
    • View Profile
Re: NHD-C0220BiZ-FSW-FBW-3V3M Problem -- Doesn't power on
« Reply #2 on: December 09, 2015, 01:06:51 AM »
Hi, Paul;

Thank you for your kind reply.

But you didn't answer my question. "Shouldn't the LCD respond by lighting up the screen, when power is connected to VDD and VSS?".

I connected the wires according to page 4. But I haven't done anything to initialize the LCD with the software yet. Nothing is happening yet. Is this expected behavior of the LCD? Are you sure that the LCD is acting normal?


I attach the picture of my hookup with MSP430F5528 EVM (I tried by the file was too large...)

The connections are like below;

RST -> VSS
SDA -> P4.1 (PM_UCB1SDA) ->  GPIO1
SCL -> P4.2 (PM_UCB1SCL) -> GPIO2
VSS -> Board voltage reference
VDD -> 3.3V of the board
VOUT -> VSS via 1uF tantalum capacitor
C1+ & CI1- connected via 1uF tantalum capacitor
10k ohm pull-up resistor connecting SDA and VDD
10k ohm pull-up resistor connecting SCL and VDD

As I told you I bought 2 pieces. I'm testing only 1 of it and the other set hasn't been removed out of the box. So, if things clear up, I'll test the other one.

I await your kind help.

Sukho

Paul_B

  • Administrator
  • Sr. Member
  • *****
  • Posts: 249
  • Karma: 16
    • View Profile
Re: NHD-C0220BiZ-FSW-FBW-3V3M Problem -- Doesn't power on
« Reply #3 on: December 09, 2015, 11:36:29 AM »
Hi Sukho,

To answer your question, No you will not see any characters appear on the LCD. Before you can really use the LCD, you must initialize and configure it. This is accomplished by sending a number of initialization instructions to the LCD.


Saurabh_B

  • Administrator
  • Hero Member
  • *****
  • Posts: 360
  • Karma: 10
    • View Profile
Re: NHD-C0220BiZ-FSW-FBW-3V3M Problem -- Doesn't power on
« Reply #4 on: December 09, 2015, 11:40:15 AM »
Also the RESET pin is active LOW.

Connect that to VDD or a GPIO pin that is HIGH.

seilcomp

  • Newbie
  • *
  • Posts: 3
  • Karma: 0
    • View Profile
Re: NHD-C0220BiZ-FSW-FBW-3V3M Problem -- Doesn't power on
« Reply #5 on: December 10, 2015, 01:28:04 AM »
Hello Paul. Thank you again.

I didn't expect to see "CHARACTORS" appear on the LCD. I know that much. What I said was it doesn't seem to "POWER ON" even when the power is applied.. Shouldn't it show me that it's not dead, at least, by way of lightening on the screen?

Cheers!

Paul_B

  • Administrator
  • Sr. Member
  • *****
  • Posts: 249
  • Karma: 16
    • View Profile
Re: NHD-C0220BiZ-FSW-FBW-3V3M Problem -- Doesn't power on
« Reply #6 on: December 10, 2015, 08:07:52 AM »
Hi Sukho,

If you would like to power on the displays backlight you will need to apply 3V @30mA (Typ.) respectively to the Anode and Cathode pins.

The wiring diagram (See page 4) shows the anode A connected to power (upward facing triangle) and the cathodes are shown connected to ground (downwards facing triangles).

http://www.newhavendisplay.com/specs/NHD-C0220BiZ-FSW-FBW-3V3M.pdf


 

NHD‐C0220BiZ‐FS(RGB)‐FBW‐3VM capacitor on pin 7&8

Started by Ticoti0xFFBoard Character LCDs

Replies: 1
Views: 2859
Last post April 09, 2014, 10:17:30 AM
by Michael_L
NHD‐C0220BiZ‐FS(RGB)‐FBW‐3VM Potting

Started by SebKisterBoard Character LCDs

Replies: 1
Views: 1875
Last post June 22, 2016, 04:51:17 PM
by Saurabh_B
NHD‐3.5‐320240MF‐ATXL#‐CTP‐1 Problem with standby mode

Started by guenterBoard TFTs

Replies: 0
Views: 2004
Last post June 16, 2016, 12:14:36 PM
by guenter
NHD‐2.4‐240320SF‐CTXL#‐FTN1 touch-screen problem

Started by hbcelebiBoard TFTs

Replies: 5
Views: 4288
Last post December 10, 2014, 11:19:05 AM
by Michael_L
Working on NHD‐2.4‐240320SF‐CTXL#‐FTN1, have problem in initialization

Started by sli25Board TFTs

Replies: 6
Views: 3900
Last post June 04, 2015, 09:52:25 PM
by sli25