Author Topic: PIC32 and NHD-C0220BIZ-FSW-FBW-3V3M problem  (Read 2677 times)

fidodido18

  • Newbie
  • *
  • Posts: 3
  • Karma: 0
    • View Profile
PIC32 and NHD-C0220BIZ-FSW-FBW-3V3M problem
« on: September 08, 2014, 11:27:32 AM »
Hello Newhaven Developers,

Sometimes the COG does not show anything on the screen, and my microcontroller show me a NACK reception of the LCD.
Please how to prevent this problem?

My system:
1. Microcontroller: PIC32MX795F512L
2. LCD: NHD-C0220BIZ-FSW-FBW-3V3M

I have 500 LCD in stock for this project. :'(

Michael_L

  • Administrator
  • Hero Member
  • *****
  • Posts: 356
  • Karma: 33
    • View Profile
Re: PIC32 and NHD-C0220BIZ-FSW-FBW-3V3M problem
« Reply #1 on: September 09, 2014, 08:41:11 AM »
What speed are you running your I2C bus at?  Also, what value pull-up resistors are you using?

fidodido18

  • Newbie
  • *
  • Posts: 3
  • Karma: 0
    • View Profile
Re: PIC32 and NHD-C0220BIZ-FSW-FBW-3V3M problem
« Reply #2 on: September 12, 2014, 08:41:05 AM »
What speed are you running your I2C bus at?  Also, what value pull-up resistors are you using?

Hello Michael L,

thank you for you help.

I have connected my LCD with extension cable (9 in).

I have 4.7 Kohm pull up resistors. And the i2c bus frecuncy is 200 khz.

Michael_L

  • Administrator
  • Hero Member
  • *****
  • Posts: 356
  • Karma: 33
    • View Profile
Re: PIC32 and NHD-C0220BIZ-FSW-FBW-3V3M problem
« Reply #3 on: September 12, 2014, 09:12:06 AM »
Thank you for the  information.  Can you please try using 10kΩ pull-ups just to test for the ACKs?  Also, is it possible to try slowing down your I2C speed to 100kHz?  I just want to see if this results in any differences for you.

fidodido18

  • Newbie
  • *
  • Posts: 3
  • Karma: 0
    • View Profile
Re: PIC32 and NHD-C0220BIZ-FSW-FBW-3V3M problem
« Reply #4 on: September 19, 2014, 10:01:32 AM »
Thank you for the  information.  Can you please try using 10kΩ pull-ups just to test for the ACKs?  Also, is it possible to try slowing down your I2C speed to 100kHz?  I just want to see if this results in any differences for you.

Hello Michael,

thank you for your help.

I have hardware problems with the RESET PIN. I changes the Microcontroller pin direction and change the pull up resistor and I2C speed and now all is OK.


thank you very much.

 

NHD‐C0220BiZ‐FS(RGB)‐FBW‐3VM capacitor on pin 7&8

Started by Ticoti0xFFBoard Character LCDs

Replies: 1
Views: 2800
Last post April 09, 2014, 10:17:30 AM
by Michael_L
NHD‐C0220BiZ‐FS(RGB)‐FBW‐3VM Potting

Started by SebKisterBoard Character LCDs

Replies: 1
Views: 1825
Last post June 22, 2016, 04:51:17 PM
by Saurabh_B
NHD‐3.5‐320240MF‐ATXL#‐CTP‐1 Problem with standby mode

Started by guenterBoard TFTs

Replies: 0
Views: 1945
Last post June 16, 2016, 12:14:36 PM
by guenter
NHD‐2.4‐240320SF‐CTXL#‐FTN1 touch-screen problem

Started by hbcelebiBoard TFTs

Replies: 5
Views: 4184
Last post December 10, 2014, 11:19:05 AM
by Michael_L
Working on NHD‐2.4‐240320SF‐CTXL#‐FTN1, have problem in initialization

Started by sli25Board TFTs

Replies: 6
Views: 3799
Last post June 04, 2015, 09:52:25 PM
by sli25