Author Topic: NHD-0420DZW-AB5 SPI Clarification  (Read 2474 times)

Analogic

  • Newbie
  • *
  • Posts: 1
  • Karma: 0
    • View Profile
NHD-0420DZW-AB5 SPI Clarification
« on: December 05, 2014, 10:09:48 AM »
I am attempting to interface the above OLED display to an FPGA using the SPI interface and the display's data sheet is not very clear.  Was hoping someone could answer a few questions for me:

1) the data sheets timing diagram shows two 10bit words output back to back.  When sending a command to the display (for example "RETURN HOME") will I need to send the bit sequence twice as the data sheet suggests: "00000000100000000010" or can I just perform a single 10 bit transfer? 

2) If the command needs to be sent twice, what does the display return in the "VALID DATA" Byte?

3) When reading the Status register or a DDRAM location, is it possible to extend the transfer (keep CSB low) on a read operation to allow continuous reading of multiple DDRAM locations or continuously query the busy flag?

4) when writing to DDRAM, can I use a single transfer (keep CSB low) to write all 20 bytes of a line?  Would the address counter be automatically incremented?

Thanks

« Last Edit: December 31, 2014, 08:47:09 AM by Analogic »

Chris O.

  • Jr. Member
  • **
  • Posts: 35
  • Karma: 5
    • View Profile
Re: NHD-0420DZW-AB5 SPI Clarification
« Reply #1 on: December 05, 2014, 09:38:48 PM »
Hi
I'm a happy user of the Newhaven-NHD-0420DZW-AY5.
But i use this datasheets http://www.adafruit.com/datasheets/WS0010.pdf

The main differences in the instructions.
1) Has a Character mode and a Graphic Mode so it requires one additional step to specify the mode which it runs in.
2) The "Function Set" instruction requires you to specify which Font Tables (2 available) to use.
3) Has a Bit in one of the instructions to allow you to turn enable/disable the internal power, Embedded DC-DC voltage converter ,Brightness DIM/FULL  :)

I'm not 100% sure if Newhaven Display use ( WS0010 OLED ) Driver/Controller IC utilizing CMOS Technology specially designed to display
alphanumeric and Japanese kana characters as well as symbols and graphics.
But i did get the Brightness DIM/FULL  control by going in the graphic mode and set the internal power ON/OFF.

I hope this helps.
Chris O.
 ;)

 

Questions regarding NHD‐0220DZW‐AY5 & NHD‐0420DZW‐AY5

Started by tseyfarthBoard OLEDs

Replies: 3
Views: 2880
Last post August 20, 2015, 09:51:26 AM
by Saurabh_B
NHD‐0420DZW‐AB5 Lines

Started by RickJBoard OLEDs

Replies: 1
Views: 2287
Last post January 09, 2015, 04:18:32 PM
by Michael_L
NHD‐0420DZW‐AY5 SPI Interface

Started by vinaykBoard OLEDs

Replies: 0
Views: 2054
Last post October 26, 2015, 05:13:10 AM
by vinayk
NHD-0420DZW-AG5 - Display "sometimes" shows only 2 lines

Started by stylonurusBoard OLEDs

Replies: 5
Views: 5586
Last post June 18, 2014, 10:09:49 AM
by Michael_L
NHD‐0420DZW‐AY5 - Power consumption and luminance difference 3.3V/5.0V?

Started by MonkeywrenchBoard OLEDs

Replies: 0
Views: 1464
Last post November 20, 2015, 06:40:16 PM
by Monkeywrench