Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - garyneal

Pages: [1]
1
Graphic LCDs / Re: NHD-320240WX-COTFH-V#I041 w/ 6809 uP
« on: April 05, 2015, 11:38:31 AM »
One more question.  I dumb one, I know, but I just want to make certain.

Can I interface the 6809 MPU (a five volt device) directly with the NHD-320240WG-BxTFH-VZ# device as shown on page four of the following document?

http://www.newhavendisplay.com/specs/NHD-320240WG-BxTFH-VZ.pdf

This device is listed to be either a 5 volt or a 3.3 volt device.

Thanks

2
Graphic LCDs / Re: NHD-320240WX-COTFH-V#I041 w/ 6809 uP
« on: April 02, 2015, 06:21:05 PM »
I did not mean power and ground were tied together.  I meant that the MPU's power and GND were common with the display's power and GND.  I understood what the triangles meant.  ;)

Your specs sheet should make it clearer that the MPU may not be directly connected to the device as indicated on page four if the MPU is powered by five volts.

Thanks

3
Graphic LCDs / Re: NHD-320240WX-COTFH-V#I041 w/ 6809 uP
« on: April 02, 2015, 03:22:15 PM »
Paul,

Thanks, but your document brings me back to my original questions regarding powering this device.

On page four of that specs document, the schematic showing the interface between the LCD device and the MPU has the power and ground lines of both devices tied together.  The 6809 is a five volt device so is that page wrong or am I allowed to power the device with 5 volts as indicated on page ten of the RA8835 controller manual linked on page five of the manual you linked?

If that page is wrong and the LCD device requires a separate 3.3 volt supply then do the address line, data lines, read/write line, etc. also need to be shifted to 3.3 volts from 5 volts?

Thanks again.

4
Graphic LCDs / Re: NHD-320240WX-COTFH-V#I041 w/ 6809 uP
« on: April 02, 2015, 11:32:21 AM »
Seven views (assuming my views did not count) but no replies so far.   :-\

I dug a little deeper and found on page ten of the RA8835 controller manual that its VDD may be the same supply as the controlling processor.  If, as I suspect, this is the same VDD pin as the subject product then it does not appear that I need a 3.3 volt regulator and level shifting.  Can someone confirm this, please?

That still leaves one other question.  How is the SEL1 line configured on the device?

5
Graphic LCDs / NHD-320240WX-COTFH-V#I041 w/ 6809 uP
« on: April 01, 2015, 06:39:00 PM »
I just recently bought the subject graphics display from Jameco:

http://www.jameco.com/webapp/wcs/stores/servlet/ProductDisplay?langId=-1&storeId=10001&catalogId=10001&productId=2190418&

The product was advertised as a 5 volt device but upon closer examination it appears to be powered by 3.3 volts.  That is not a problem but I am kind of confused and need some clarification on a couple of things.  I apologize for the newbie question but I have not actually built a project that utilizes an LCD display before and I want to ensure that I interface the uP and the device up correctly.  The product specs sheet shows on page 4 that the VSS and VDD terminals are both wired to the same VSS and VDD terminals of the MPU.  Since the 6809 is a 5 volt device does the LCD device accept a 5 volt supply or is that an error on the specs sheet?  If it is an error does that mean that the data and control lines from the MPU require level shifting to 3.3 volts or can they be wired directly to their corresponding pins of the LCD device?

Lastly, SEL1 line is indicated as non connected and a jumper JSEL selects the SEL1.  Is this device configured for the 6800 family MPU or 8080 family?

Thanks for your help.

Pages: [1]