Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ED

Pages: [1]
1
OLEDs / Re: NHD-3.12-25664UCB2-ND dim display with banding?
« on: May 02, 2016, 09:14:56 AM »
I made a measurement.
  With 2 bright lines at the top it draws 8mA.
  Then as the lower half is filled the current increases to 8 then 10 mA.
  With the command to turn the entire screen on it rises to just 11mA.
  This was measured with a large desktop suppy set at a mak of 5Amps..

This sounds to little - other users seem to be quoting figures upto 170mA.....

Ok - so I have now moved the cables around and the display is fine - the flickering is gone and . The problems seems to be due to bad contact on the breadboard - I guess the combination of large pins soldered to the display opening up the tracks and narrow pins on the jumper leads don't work well together when higher current is needed!

Thanks for all your help, regards, Edwin

2
OLEDs / Re: NHD-3.12-25664UCB2-ND dim display with banding?
« on: May 02, 2016, 02:27:18 AM »
I tried the u8glib library over the weekend. The graphicsTest example on the face-of-it  looks good. However, if I increase the size of the rectangle to almost fill the screen (line 151), then the rectangle dims and and the horizontal bands reappear.

Just to confirm I am running the display with a 3.3V psu and changing the voltage level from the UNO

Regards

3
OLEDs / Re: NHD-3.12-25664UCB2-ND dim display with banding?
« on: April 27, 2016, 02:07:39 AM »
Thanks for the replies

  I have changed the program to start at line 32 and fill the lower half of the screen. All the pixels are filled/accessibe, but again the display dims visibly as you go down and there is some horizontal banding.
  If I send FF to all the pixels then it seems to work, but the display is very dark and it is difficult to tell.
  I also increased the delay after the turn display on command (A5h) and horizontal lines were obviously present.

  Finally! I  tried writing a couple of lines in the top half followed by lines in the lower half. This worked, however the initial 2 lines were BRIGHT (what I would imagine is normal), as more pixels are drawn then the display gets dimmer and dimmer - it almost looks like as there is something wrong with the psu, and if too many pixels are illuminated then the banding appears or it turns black. Is there any test that would show the psu is OK. Using a voltmeter on pins 1 and 2 it sits at 3.28V all the time.   


  Thanks also to the link to the /u8glib library -  I'll give it ago.

Regards, Edwin

4
OLEDs / NHD-3.12-25664UCB2-ND dim display with banding?
« on: April 25, 2016, 04:33:17 AM »
I have a NHD-3.12-25664UCB2-ND which I am trying to use via 4wireSPI with an Arduino.

I have set the system up using the "checkerboard example" (https://github.com/MartyMacGyver/OLED_SSD1322/blob/master/Arduino/SSD1322_NHD_256x64_mono_demo/SSD1322_NHD_256x64_mono_demo.ino) and settings taken from your NHD-3.12-25664UCY2 flickering post  / datasheet p12 (http://www.newhavendisplay.com/NHD_forum/index.php/topic,875.msg1707.html#msg1707).

When I run the code the communications seem fine - at least the screen turns on/off with the commands as expected.
The problem seems to be when writing pixels to the screen. Initially it seems fine the first rows of pixels appear brightly. However, they then quickly dim and by the time the it is on around the 20th row it fades away and the screen is almost black. There is also a lot of horizontal banding with the display dimming as you do down (see image). I thought it could be a problem with the PSU, so am now using a 3.3V 2Amp to ensure it is powerful enough.

Do you have any idea what is wrong - or can you point me to other working Arduino projects.

Many thanks

Pages: [1]